Skip to main content

Order proposals: calculation, prerequisites and missing products

Here is how Scopevisio calculates order proposals, which prerequisites a product must meet and why a product may be missing from the order proposal.

This article shows how Scopevisio calculates order proposals, which sources and prerequisites apply, which supplier appears in the proposal and what to check if a product is missing from the order proposals. How to check, adjust and transfer order proposals is described in the article Check, adjust and transfer order proposals to an order.

How Scopevisio calculates order proposals

Scopevisio creates order proposals, but no purchase orders. Replenishment planning calculates order proposals when events occur and additionally once a day. The purchase order is only created when you transfer the order proposal.

Sources of an order proposal

The following table shows the two types of demand from which an order proposal arises.

Type of demand

When does an order proposal arise?

Reorder point undercut

The stock of a product is below the reorder point that you have stored per product and location or storage bin. The next replenishment planning (when events occur and daily) creates an order proposal up to the maximum stock. The order proposal is not created immediately when the goods are withdrawn.

Order shortfall

One or more orders or requirement requests cannot be fully fulfilled with the existing stock and open purchase orders. Scopevisio proposes the missing quantity for ordering.

If both types of demand apply to the same product at the same time, Scopevisio adds the quantities.

Order quantity for an order shortfall

For an order shortfall, the order proposal does not calculate the quantity ordered in the customer order, but the actual shortage: order quantity − stock − quantity already ordered. Scopevisio sums the shortage across all open customer orders and across products.

The following calculation examples show the calculation for one product:

  • An order comprises 100 units, 40 units are in stock: The shortfall and thus the order proposal is 100 − 40 = 60 units

  • An order comprises 100 units, 40 units are in stock and 10 units are already ordered: The order proposal is 100 − 40 − 10 = 50 units

For the calculation via order shortfall, you do not need to maintain a reorder point or a maximum stock. The maintenance effort is therefore low.

Prerequisites for a product in the order proposal

A product from an order only appears in the order proposal if all three conditions are met:

  • The product has a base unit.

  • The product type of the product is marked as reservable in the procurement settings.

  • The product is not blocked.

Further causes for missing order proposals are described in the section "If a product is missing in the order proposals".

Which supplier appears in the order proposal

Replenishment planning preferably selects the default supplier of the product for the order proposal. If no default supplier is stored, it selects another supplier of the product that is valid on the order date. A default supplier has no validity period.

A default supplier is not a prerequisite for an order proposal. If the product has no valid supplier, Scopevisio creates the order proposal without a supplier. Then enter a supplier before saving or ordering.

Before transferring to a purchase order, you can change the supplier in the order proposal to another maintained supplier of the product.

If a product is missing in the order proposals

An empty list of order proposals can have two different causes.

Situation

What it means

Order control shows green or yellow, there are no open order proposals

Everything is covered. Stock and open purchase orders are sufficient for all orders and reorder points. No action is needed.

Order control shows red, but no order proposals are visible

Scopevisio cannot create an order proposal for the product concerned. The cause lies in the master data (see the following checklist).

For the product concerned, check in sequence which check item applies:

Check item

Where to check

Base unit stored?

Product → Stammdaten tab → Base unit. Without a base unit, Scopevisio does not take the product into account.

Product type marked as reservable?

In the procurement settings. Scopevisio only takes products with a reservable product type into account.

Product blocked?

Scopevisio does not take blocked products into account.

Product assigned to the correct location?

Scopevisio calculates order proposals per location. Check whether the order and the product have the same location.

Note: If a supplier is missing, the order proposal is not missing. Scopevisio creates it without a supplier. In this case, check whether a supplier valid on the order date is entered for the product on the Product suppliers tab.

If the problem persists, ask in the chat to be connected with the support team.

Related articles

Did this answer your question?